ISO 4892-2 Xenon Arc Lamp Acceleration Aging Environmental Test Chambers
Complied Standards & Clauses
ASTM G155 Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
AATCC16 Colorfastness to Light
ISO 105-B04:1994 Textiles - Tests for colour fastness - Part B04: Colour fastness to artificial weathering: Xenon arc fading lamp test
ISO 4892-2:2006 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps
ISO11341:2004 Paints and varnishes-Artificial weathering and exposure to artificial radiation-Exposure to filtered xenon-arc radiation
ISO 16474-1:2013 Paints and varnishes -- Methods of exposure to laboratory light sources -- Part 1: General guidance
IEC60068-2-5:2010 Environmental testing-Part2-5:Tests-Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing
Equipment Overview
This equipment reproduces the destructive light waves existing in different environments by simulating the xenon arc lamp of the full sunlight spectrum, and can provide corresponding environmental simulation and accelerated tests for scientific research, product development and quality control.
The aging test is carried out by exposing the material sample to the light and thermal radiation of a xenon arc lamp to evaluate the light resistance and weather resistance of some materials under the action of a high temperature light source. Mainly used in automobiles, coatings, rubber, plastics, pigments, adhesives Agents, fabrics, aerospace, ships and ships, electronics industry, packaging industry, etc.
This xenon lamp weather resistance tester can be used to select new materials, change existing materials or evaluate changes in durability of materials after changes in composition. It can well simulate changes in materials exposed to sunlight under different environmental conditions.
Technical Parameters
| Model | SN883-280L | SN883-500L | SN883-1000L |
| Inner box size w*d*h (mm) | 600×600×800 | 800×800×800 | 1000×1000×1000 |
| Outer box size w*d*h (mm) | 1200×1345×1900 | 1400×1545×2100 | 1600×1745×2300 |
| Diameter of turntable (mm) | Ф400 | Ф600 | Ф800 |
| Temperature range | Rt+10℃～70℃ |
| Black mark temperature | 40℃～100℃ adjustable (light cycle); 25～85℃ (dark cycle) |
| Humidity range | 30%～98%rh (dark); 20%～60%rh (light) |
| Temperature uniformity | ±3℃ |
| Temperature accuracy | ±0.1℃ |
| Humidity accuracy | ±1％rh |
| Temperature and humidity sensor | Pt100ω/mv platinum resistance |
| Turntable speed | 1～3r/min |
| Tube light source | 1 water-cooled demostic lamp or imported brand lamp |
| Lamp life | Around 1200 hours |
| Lamp power | 6.5KW |
| Effective exposure area | 3760cm2～7500cm2 |
| Light cycle time | 1～999h, m, s continuously adjustable |
| Rain time | 1～9999min continuous rainfall adjustable |
| Rain cycle | 1～240min interval (off) rainfall adjustable |
| Water spray cycle | 18min/102min or 12min/48min (water spray time/no water spray time) |
| Spray water pressure | 0.12～0.15mpa |
| Nozzle aperture | Ф0.8mm |
| Standard sample size | 75mm×150mm |
| Filter type | Window glass filter, solar filter, uv filter, you can choose any one |
| Xenon lamp radiation intensity | 290～2450nm band 400～1120w/m2 |
| 420nm band, 0.55～1.1w/m2 |
| 340nm band, 0.35～0.7w/m2 |
| 300～400nm band, 40w～60w |
| Material used | Outer box material: sus201 stainless steel or cold-rolled sheet paint |
| Inner box material: sus304 high quality stainless steel |
| Sample holder material: sus304 high quality stainless steel |
| Door frame: high and low temperature aging resistant silicone rubber door seal |
| Conditions of use | Voltage: 380±10%v, 50±1%hz, power 15kw three-phase five-wire system |
| Environmental conditions | Temperature 5℃～30℃ relative temperature ≤85％rh air pressure 86kpa～106kpa |
| Safety protection device | Leakage, short circuit, over temperature, water shortage, motor overheating, overcurrent protection |
Product Tags:
|
|
ISO 4892-2 Xenon Arc Lamp Acceleration Aging Environmental Test Chambers Images
|
